| Close window command? [message #49395] |
Mon, 24 July 2006 12:32  |
adisn123
Messages: 44
Registered: July 2006
|
Member |
|
|
Hello,
My program generates 4 different images in 4 different window in one
operation.
It is quite tedious to close every window after display to run the
program again after I change some
parameters in the program in order to see new 4 images.
I'm wondering there is a way to kill/close the old windows when the
program starts over.
Thank you.
|
|
|
|
| Re: Close window command? [message #49488 is a reply to message #49395] |
Mon, 24 July 2006 13:59  |
adisn123
Messages: 44
Registered: July 2006
|
Member |
|
|
Thank you all for the advice above.
Those were the ones that I was looking for exactly.
Thanks again.
Paul Van Delst wrote:
> Mike Chinander wrote:
>> In article <1153769529.483637.316050@h48g2000cwc.googlegroups.com>,
>> <adisn123@yahoo.com> wrote:
>>
>>> Hello,
>>>
>>> My program generates 4 different images in 4 different window in one
>>> operation.
>>>
>>> It is quite tedious to close every window after display to run the
>>> program again after I change some
>>>
>>> parameters in the program in order to see new 4 images.
>>>
>>> I'm wondering there is a way to kill/close the old windows when the
>>> program starts over.
>>>
>>> Thank you.
>>>
>>
>>
>> This should delete all open windows:
>>
>> IDL> while !D.WINDOW ne -1 do wdelete
>>
>> if you know the window indices of the four windows your program creates, you can do:
>>
>> IDL> wdelete, w_ind1, w_ind2, w_ind3, w_ind4
>>
>> where w_ind1, w_ind2, ... correspond to the window indices of your open windows.
>>
>> Hope that helps,
>
> Or, if you want to add more open windows in the future (hey, computer screens are getting
> bigger all the time!) you could do:
>
> nWin=4
> winID=lonarr(nWin)
> for i=0,nWin-1 do begin
> window, /free
> winID[i]=!d.window
> endfor
>
> ...do stuff....
>
> ; plot to first window
> wset, winID[0]
> plot, .....
>
> ; plot to second window
> wset, winID[1]
> plot, .....
>
> etc....
>
> ; done
> for i=0,nWin-1 do wdelete, winID[i]
>
>
> ?
>
> Increase nWin as required.
>
> Using the above you could have additional windows open that you *don't* want destroyed
> every time you rerun your code.
>
> Or, even more simply, you could just do
> !p.multi=[0,2,2]
> and avoid the multiple windows altogether. :o)
>
>
> paulv
>
> --
> Paul van Delst Ride lots.
> CIMSS @ NOAA/NCEP/EMC Eddy Merckx
> Ph: (301)763-8000 x7748
> Fax:(301)763-8545
|
|
|
|
| Re: Close window command? [message #49490 is a reply to message #49395] |
Mon, 24 July 2006 13:23 |
Paul Van Delst[1]
Messages: 1157
Registered: April 2002
|
Senior Member |
|
|
Mike Chinander wrote:
> In article <1153769529.483637.316050@h48g2000cwc.googlegroups.com>,
> <adisn123@yahoo.com> wrote:
>
>> Hello,
>>
>> My program generates 4 different images in 4 different window in one
>> operation.
>>
>> It is quite tedious to close every window after display to run the
>> program again after I change some
>>
>> parameters in the program in order to see new 4 images.
>>
>> I'm wondering there is a way to kill/close the old windows when the
>> program starts over.
>>
>> Thank you.
>>
>
>
> This should delete all open windows:
>
> IDL> while !D.WINDOW ne -1 do wdelete
>
> if you know the window indices of the four windows your program creates, you can do:
>
> IDL> wdelete, w_ind1, w_ind2, w_ind3, w_ind4
>
> where w_ind1, w_ind2, ... correspond to the window indices of your open windows.
>
> Hope that helps,
Or, if you want to add more open windows in the future (hey, computer screens are getting
bigger all the time!) you could do:
nWin=4
winID=lonarr(nWin)
for i=0,nWin-1 do begin
window, /free
winID[i]=!d.window
endfor
...do stuff....
; plot to first window
wset, winID[0]
plot, .....
; plot to second window
wset, winID[1]
plot, .....
etc....
; done
for i=0,nWin-1 do wdelete, winID[i]
?
Increase nWin as required.
Using the above you could have additional windows open that you *don't* want destroyed
every time you rerun your code.
Or, even more simply, you could just do
!p.multi=[0,2,2]
and avoid the multiple windows altogether. :o)
paulv
--
Paul van Delst Ride lots.
CIMSS @ NOAA/NCEP/EMC Eddy Merckx
Ph: (301)763-8000 x7748
Fax:(301)763-8545
|
|
|
|
| Re: Close window command? [message #49491 is a reply to message #49395] |
Mon, 24 July 2006 12:50 |
mchinand
Messages: 66
Registered: September 1996
|
Member |
|
|
In article <1153769529.483637.316050@h48g2000cwc.googlegroups.com>,
<adisn123@yahoo.com> wrote:
> Hello,
>
> My program generates 4 different images in 4 different window in one
> operation.
>
> It is quite tedious to close every window after display to run the
> program again after I change some
>
> parameters in the program in order to see new 4 images.
>
> I'm wondering there is a way to kill/close the old windows when the
> program starts over.
>
> Thank you.
>
This should delete all open windows:
IDL> while !D.WINDOW ne -1 do wdelete
if you know the window indices of the four windows your program creates, you can do:
IDL> wdelete, w_ind1, w_ind2, w_ind3, w_ind4
where w_ind1, w_ind2, ... correspond to the window indices of your open windows.
Hope that helps,
--Mike
--
Michael Chinander
m-chinander@uchicago.edu
Department of Radiology
University of Chicago
|
|
|
|
comp.lang.idl-pvwave archive
Members
Search
Help
Login
Home
