| OPLOT fails intermittently, any ideas? [message #25807] |
Mon, 16 July 2001 12:05  |
bleau
Messages: 24
Registered: November 1993
|
Junior Member |
|
|
Hello, IDLers, I have a tricky problem here. First, my config: I'm on OpenVMS
7.1-2, running IDL 5.2. I'm using PLOT and OPLOT to generate a graph for
display on a web page. Most of the time this works well. Once in a while,
though, with no change in the IDL code, I get the error message
% OPLOT: No valid points, must have at least 2 distinct points
% Execution halted at: $MAIN$ 253
DISKM1:[SOHO.TEST]SEM4HRPLOT_MAIN.PRO;27
Line 253 is the oplot command. Here it is:
oplot, epoch-base_epoch, values(*,k), $
max_value = 9999998., $
psym = 8, $ ; plots a circle (user defined)
symsize = .4, $ ; scale factor for plot symbol
thick = plot_thickness(k), $
color = 13 ; change this for colored data line
A word here about the odd construct. The X array is a double precision vector
(epoch) containing times minus a scalar (base_epoch), which is slightly less
than the first (lowest) value of epoch, which is monotonically increasing.
Since plot and oplot convert from double to single internally, when labelling
the time axis this causes incorret labels to be used. By passing the
difference this puts the values to be plotted in a range in which roundoff is
not a problem. The X range that was set on the previous plot command has been
adjusted similarly.
Here's a diagnostic output; the first column is the date in Gregorian format,
the second in Epoch format, and the third in Epoch format minus the base_epoch
value. The two lines are the low and high end used for the x-axis range; the
third colum is what I passed to the previous call to plot for the x_range
keyword.
range used on X-axis is:
2001/07/16 11:00:00 3.6412920e+08 0.00000000
2001/07/16 15:00:00 3.6414360e+08 14400.000
I checked the arrays being passed to oplot; both are vectors of length 410.
I also dumped a couple points in the x-axis vector (epoch) to make sure they
are different; they are. The y-axis values look fine, too. Here's the output
of the following commands:
help,epoch-base_epoch
<Expression> DOUBLE = Array[409]
help,values(*,k)
<Expression> FLOAT = Array[409]
print,values(0,k)
2186.24
print,fmtepoch(epoch(0))
2001/07/16 11:00:46
print,fmtepoch(epoch(408))
2001/07/16 15:03:01
print,fmtepoch(base_epoch)
2001/07/16 11:00:00
print,epoch(409)-base_epoch
14581.000
I'm puzzled by the error message that oplot gave me (No valid points, must have
at least 2 distinct points). The obvious reason - one of the vectors has only
one point - is false, as seen above.
The second reason I thought might be the case is that the range given to the
plot command, and therefore in use for the call to oplot, did not contain the
values passsed to oplot for the x-axis. This, too, is shown to be false.
I'm out of ideas. What's worse, this problem is not consistent. It appears
every few days, once that day, then goes away. This IDL code is called from a
procedure that runs hourly and works on slightly different data each time. So
it would appear to be data dependent. I managed to save a copy of the data set
that caused it to fail today, and can reproduce the failed behavior, so I have
a chance at diagnosing this. I just need some hints at where to look next.
Thanks.
Lawrence Bleau
University of Maryland
Physics Dept., Space Physics Group
301-405-6223
bleau@umtof.umd.edu
|
|
|
|
comp.lang.idl-pvwave archive
Members
Search
Help
Login
Home
